|
BTM-01
StarCom1 Bluetooth Module
Introduction
 
Measuring only
1¼" x ¾"
x 1¾"
Install with Starcom1, then leave your bluetooth enabled
phone in your pocket, it will automatically connect each
time you get on the bike.
The Starcom1 bluetooth module is designed to allow
cordless and automatic operation of bluetooth compatible
mobile phones with the StarCom1 unit.
BTM-01
Bluetooth is a short- range wireless communication
technology. It allows wireless connections between Bluetooth
devices such as cellular phones, personal digital assistants
(PDA), desktop and notebooks computers, input-output devices
(mouse, keyboards, printers), home appliances. Bluetooth
refers to a worldwide standard designed to operate in the
internationally recognized ISM (Industrial Scientific and
Medical) frequency band. Within the ISM band (2.4Ghz -
2.48Ghz) Bluetooth transmissions hop between 79 separate
frequencies 1,600 times every second, and with a
communication range of about 10 meters (class II).
Bluetooth
Class 2 product with compliance to specification v11.1 and
full FCC and CE certification.
Installation instructions
must be followed carefully.
Installations must only be undertaken by a person who has a
full understanding of the electrical, safety and mechanical
requirements involved. If in any doubt, please consult your
dealer.
Unit Installation
The unit must be operated from a switched vehicle 12V DC
supply. The unit is water-resistant but not waterproof
so care must be taken to keep it dry. Care must be taken
not to mount the unit near areas which will get hot, for
example, near the engine or exhaust. Also the unit must
not be placed close to the ignition system; HT leads
coil, alternator, or parts of the bike that could cause
electrical interference.
Power Cable Installation
The unit requires a 12V vehicle supply it has a built-in
voltage regulator, reverse input protection and fuse, so
that it is safe to use directly from a vehicle’s
switched supply. A power cable is supplied along with an
in-line fuse and fitting kit.
The 12V supply must be ignition switched, so that the
BTM-01 supply is off when the vehicle ignition if OFF
else the vehicle battery may be drained.
The Jack plug cable must be plugged into the phone
socket on Starcom, this provides the 0V connection.
1) If the StarCom 12V supply is ignition switched supply
then the BTM-01 12V connection can be made by splicing
into the starcom power cable.
2) If the StarCom is connected to the battery directly
then the BTM-01module must be connected to a switched
supply.
Paring Headset
You are required to pair the BTM-01 with your mobile
phone or other devices before using it.
Step 1: The BMT-01 must be connected to StarCom and
powered ON before initiating pairing. To initiate
pairing, press and hold pairing button for 5 seconds
until the red indicator of BMT-01 is slowly flashing.
Step 2: Initiate pairing process of your mobile phone.
Refer to the manual of mobile phone for details of the
process. You will see a new item "StarCom1" added in
your Bluetooth device list after the searching process
completes.
Step 3: You will be asked to enter pin-code to complete
pairing, enter 0000 and confirm it. (Note: The
0000 is default pin-code pre-stored in BTM-01.) The red
indicator will turn off after pairing completed
successfully.
Note:
1. If the BTM-01 is not in pairing mode, your mobile
phone won't find the BTM-01.
2. You may need to repeat steps 1 to 3 until pairing
succeeds.
3. Pairing is a process of associating Bluetooth devices
with each other. It will establish a permanent security
link between the devices and enable quick access to the
services provided without the need to enter passkeys.
4. Paired devices remain paired even when:
- One of the devices is not powered on.
- A service connection is interrupted or the service
stopped. - One or both devices are rebooted.
Fitting Kit
5x short tie wraps 1x scotch lock splice 1x loop
Velcro 1x hoop Velcro |
